I'll happily field anything,you may wish decerned.

If you wish it decerned twice,I can do that.

What are the optimum components to build a .223 Ackley improved?

What's the role?

Blacktail deer rifle.

Anything twisted 1-14" or faster and 20" or better in length,will wreak havoc.

The 53TSX will yield 3500fps,trajectories are modest,impact energy and impact velocity...well beyond "adequate".

If you've a Remmie,thought should be cast towards faster twisted aspirations,because the latitude opens windows of opportunity. Mag confines can be juggled,to allow the 62TSX a 3400fps initial launch and with that comes more residual juice.

Have killed many via 53,but the 62 is new enough,that I've only shot it on paper.

That being said,I do not fret the 62's employment,as I decern it very capable.

7mm mag for elk

Amongst others,equally as capable.

Wow - sounds like you know your stuff!

I've got a custom 30-06 built on a large ring K-98 mauser action.

I read some articles online about using 30-06 loads tipped with 165 or 168 gr Barnes TSX for BOTH mulies and elk...

Right now I use two separate factory rounds for each season (your standard 150gr deer, 180gr partition elk), but 1 for all would be nice.

Thoughts on the 165gr for elk?? Factory (Fed Prem.) or handload?

Yes,
HD knows how to put together a blackie smokin unit.
No doubt about it!
Sal

Bullet weight,is a misnomer in this day and age as focal evaluatory criteria,same goes focus on meaningless designators,such as Sectional Density(SD).

Bang for the buck,the 165/8's in .308" bores,is a very sound answer to any situation,but many Wive's Tales remain and often folks are entranced with the designators that bear the least amount of fruit. Dumb ideas,die hard.

The 168TSX is without peer and I like that the 168A-Max(Hornady) dupes it's BC,so one can interchange through the course of the year,less major sight setting concerns. Typically,in a sound rifle,they will print on top of each other,when launched at like speeds.

I find much to get excited about,when my practice/play loads are in synch with the load I use to fill tags. I shoot those two projectiles in harmony,from most everything from 308Win to 30-8mmRemmag (a Wildcat,that is essentially a stretched 300Wby or 7STW necked up).

You will not be able to keep the 168TSX inside an Elk,at any angle,from most any distance(they'll get you to the 1000yd line,nicely).

Same goes Mulies.

You'll find that the familiarity of the 2 projectiles,will essentially mean that you are shooting a single load for everything and in that approach,everything becomes a little sweeter.

The harmonious melding of an X,with a like BC practice/play bullet,is something I strive for in every rifle I shoot,from 223AI right up the line to the Boomers.

It never don't work.

Hog Daddy I have 2 questions

1. I have an remington model 788 in .308. There is some rust pits in the barrell. New barrell job cost more than it is worth. Really enjoy the accuracy of this rifle. What would you do?

2. I have a single shot 45-70 govt. and I want to make some hanloads for it. I dont want the flat nose or round nose bullets that are common because of lever action safety. It is a modern chamber and I can exceed the pressures over what is recomended for black powder cartriges. Have you seen any pointed boat tail bullets in .457"? If so do you have any loading info for loads slighly over black powder cartridge pressures. I dont want to test the steel, I just want to be a little faster and more aerodynamic than the factory loads that are universal to old and new firearms.

1) I've a few 788's,they are fair to middlin'. They typically shoot very well,but what Remington doesn't?

The rear locking bolt lugs,are a concession,for high round count forays. They can also be hard on brass,due to some flex.

Weighing what a new barrel costs,I'd cut my losses,let it go for whatever I could get out of it and then upgrade(twin locking lug Remmie),less ever looking back.

2) The .458" bore is a niche that though very well supported in projectile selection,it doesn't have any high BC Mojo going on for it.

The 500gr X has a BC of .526 and that is the widest window of opportunity,that I'm privvy too(.375's is the upper echelon of my interests).

If you wished to cast your own,you could spec a mould of your own design and go that route.

Thanks for the info on the TSX....good stuff! Next is a muzzleloader question:

Best projectile for SW Wash elk? (.54 T/C System 1) ...prefer sabots for accuracy, but selection is limited with the 'all-lead' rule in Wa. Older ML, so max charge is 100gr.

...thoughts?

Rem. 700 .243
Used to shoot it all the time on greydiggers/chucks, been in the safe for years and want to rekindle the fire. Where to start? Barrel is probably copper fouled. Best method to clean out? Lapping bullets?? Would like to possibly re stock it but it is left handed, any suggestions. Like the HS precision but can't find LH.
Purpose: West coast blacktails. 300yd capable.
fond of the 95gr partition, powder ?? Any insight would be appreciated. HT

Rem 700 .222rem
Brand new factory rifle std. bbl.
Purpose: around the place fun gun, as tight of groups as I can produce with a sporter wt. rifle. Very fond of this cal. Heard ball powder might be the best?? When are bench rest primers worth it? Thanks again HT

I am not Hog Daddy, but I know him personly, and have learned much about rifles from him. I will give you what I know since he isn't allowed to post on this board any more.

Barnes CR-10 is very good at removing copper. I had an electronic cleaner thing for a while, but they are a pain in the a$$.

Reloader 15 works real good in .243, and a lot of other cartridges too !

Barnes TripleShock bullets work real good on game...they will penetrate, they will expand, and they will not come apart, the Noslers you mentioned can't say that with reliability.

I have shot several of Hog Daddy's rifles, and from that I can say that I agree with him about which stock shape I like, though I don't own one myself yet, it is the Remington Classic made by McMillan. You can get the Classic any way you want it, left hand is no problem, you can specify length, weight, color, options, etc. McMillan's has a website, and you may even find a stock available on their web special section ( cheaper and faster, but not custom to your wishes), otherwise be ready to wait a month or two for your stock, but they are by far the best stock in most peoples mind.

I hope that helps...anybody going by "hooktender" can't be too bad of a guy...........

P.S., those left handed Model 700's are junk, how much do you want for it ?

You say fond of the caliber, me to, but why not change the cartridge to .223 Ackley ? You could have the same barrel re-chambered and gain some speed, and maybe accuracy as well, (new chamber probably better than factory)...

Either way I think H335 powder is going to be hard to beat.

I would definately use Hornady V-Max bullets, 50 grain, or maybe 40 grain if shots mostly close. These are very accurate, and basicly vaporize small critters...you won't be disapointed.

I think I get 50 grainers to over 3800 fps in my 23" 223 Ackley barrel. I used a number 3 contour Douglas barrel, and a McMillan Mtn Rifle stock, I wish I had used a Classic, and intend to change that out when my priority list allows.


P.S. those .222's are junk too, how much do you want for it ?

Forgot about the primer question.

I haven't used benchrest primers, but have made some very accurate ammo with plain old CCI primers, I think you would have to get way down the super accuracy trail before there would be any chance to realize any benefit from the yucky-muck primers. Some primers are made of tougher metal though, in other words you can get away with running hotter loads without piercing, or cratering them. I don't know which primers are best, but I would take CCI first and Winchester last.

Hopefully someone with more experience will chime in...

I have used v-max and nosler balstic tips on rock chucks and grey diggers. I liked them both but I have never seen VAPORIZATION like the time I loaded 110 grain hollow point Speers on .30-06 brass. Got them screaming well over 3200 with GOBS of energy. SPLAT!!!!


Have you come across a good synthetic thumb hole stock for ruger MKII LA. Seen a couple of wood ones but I didn't want it. Would like one like my Win mod 70 varmit but in thumb hole fashion.