What do you want to refinish?

Use a mild liquid stripper to remove all/most of the old finish. As for removing the old finish in the checkering, just scrub it with some old toothbrushes and blot it up with paper towels after the stripper has had time to do its work. Time consuming, but it will work. And as for sanding the stocks without blunting the sharpness of the checkering, use painters tape, trim it to fit each checkered pattern with an X-acto knife, and then just sanding carefully around these masked areas if needed. You can steam out many dents/dings with a damp cloth and cloths iron.


Just to confuse you more, here is why I chose my finish.

Tung Oil is applied by just rubbing it in with a rag. The process is identical to Tru Oil, but I just think Tung Oil is a little easier to use. Like with painting more LIGHT coats are better. Resist the temptation, when I say LIGHT I mean 1/3 the amount of oil you think.

My process went like this...

Preparation:
Strip the old finish.
Sand / steam out any imperfections.
De-whisker. This should be very little because you are refinishing and not doing a lot of sanding.

Day one:
Apply one coat of Tung Oil everywhere. coverage is key for this first coat.
Wait 30 minutes and it should be dry to the touch.
Apply another coat.
Wait until the next day.

Day two:
Sand lightly with 400 grit using a sanding block, not the checkering. The sanding block is important.
Apply Tung Oil everywhere.
Wait 30 minutes. It should be dry to the touch. If not, wait until it is.
Apply another coat.
Wait until tomorrow.

Day three:
Sand lightly with 400 grit using a sanding block. Never the checkering.
Evaluate the finish. If you see little shiny spots, the grain has not been filled in.

At this point you have two options because the gain must be filled in to get that professional finish. You can repeat the 400 grit every day until the grain is filled in or you can do a slurry. Do do the slurry, instead of sanding dry, use the Tung Oil to sand with. This will create a slurry made up of the fine saw dust from sanding. This will fill in the grain much quicker. The long method is better, but it would take a keen eye and a magnifying glass to tell the difference. I chose the long method.

Apply a coat of Tung Oil.
Wait until tomorrow.
Repeat until the grain is filled in. (you see no shiny spots after sanding)

Day x:
Run your hand over the cured finish. You will feel some spots where dust has settled on your stock. Unless you have a sealed room, this will happen.
Use 600 or 800 grit and lightly sand again.
Wipe the stock thoroughly to remove any dust.
Wait at least one hour to let the dust settle. It would be better to move to another room where no sanding has been done.
Apply one thin coat. No need to go into the checkering with this coat.
Wait until tomorrow.

Day x+1:
Evaluate the finish. As you run your hand over the finish, you will still feel the little pieces of dust. They should be very light. How does the shine look to you?
Once you have a coat or two applied after the gain was filled in, you can begin to get the end result.
At this point I leave the sand paper behind. I will only use an old t-shirt to rub the finish down. Believe it or not, the t-shirt will take off the little dust particles and shine things up a little.

Keep doing this process until you have the shine you want. Resist the urge to stop after applying a coat and letting it cure. The final step must be a rub down with the t-shirt. If you don't, your finish may not be sturdy enough to stand up to regular use and will show scratches easily. Also, don't start rubbing too early. If the finish is not fully cured you'll bugger it and have to sand it down and start the final steps again.

I'm not a pro. This is just what I did and I'm very happy with the result. It's a long process, but worth it in the end. If you follow it, you will be happy too. What you don't want is to hear, "Did you re-finish this yourself?" Trust me, people can tell. What you do want is to hear people say, "Wow, that stock looks great!" Then you can say that you did the finish yourself and watch their surprise.